Jody Lo

B U R N I N G

If you are the proud owner of new Jody Lo candle, it is important to follow the instructions carefully before lighting your candle to guarantee a perfect use. In order to maintain the JODY LO Candle in an efficient and effective manner, adequate maintenance need to be provided. We recommends you follow the following safety instructions (on the box & under the candle). Take the candle out of its luxury packaging and just light the candle. Do not cut the wicks. They are ready for use.

I N S T R U C T I O N S

BEFORE BURNING


STEP 1

We advise you to place your candle away from any air flow to ensure an even burn. For multiple-wick candles, always light all the wicks. A candle must burn evenly on its entire surface. Initially, let the candle burn 3 hours in a row so that the first layer is completely melted in order to have a nice effect. We work with high quality pre-waxed cotton wicks. Therefore, it is not necessary to cut the wicks before each use. If the wick became to long (more than 1 cm), cut the wick with scissors. This will prevent the flame becomes too high and produces too much smoke.


WHILE BURNING


STEP 2

Wait until the entire surface has been liquefied in order to obtain an even burn. Do not allow your candle to burn more than 4 hours so that the perfume does not deteriorate and in order to allow enough oxygen in the glass so that it burns correctly. A candle which no longer has oxygen will subsequently burn less. Do not burn the last cm of wax in order to avoid accidents. Do not blow out your candle, but place the wicks in the wax and straighten them out again.


AFTER BURNING

STEP 3

Once the wax solidifies again, we advise you to straighten the wicks out. Periodically clean the inside of the glass with a damp cloth so as to remove the soot.


Are Jody Lo candles rechargeable?


FAQ

Due to their artisanal fabrication, Jody Lo candles are not rechargeable.

Since the glass is hand-blown, each container is unique. Each one’s size and shape varies. It is therefore impossible to create a recharge that can fit all candles. For safety reasons, the wicks must be glued to the bottom of the glass in order to avoid any slide at the edges when the candle reaches its end.


The wicks don't seem to be burning as they should, the flames are becoming smaller, what should I do?

FAQ

If your candle isn't burning normally, it might be a sign that the wicks are too close to the melted wax and, therefore, drowning in it. In order to fix this problem, first extinguish the candle. Our advice is to then check if the wicks are standing straight (and, if not, to adjust them) and to, potentially, remove a bit of melted wax with a little spoon. Please wait at least 15 minutes before lighting up the candle again.

The wax isn't burning evenly on the surface, why is that?

FAQ

In order to burn evenly, all the wicks of the candle should be lit. To prevent the formation of "craters" in your candle, you should avoid extinguishing it before all the wax surface has melt evenly.

Another reason for this issue might be a slight breeze. Although sometimes unnoticeable for us, air movements can interfere with the smooth burning of your candle. For this reason, we advise to rotate the candle from time to time if faced with this problem.

Donec mauris purus sodales eget enim, ultrices nulla feugiat porta fringilla pellentesque vulputate.

W I C K S

Donec mauris purus sodales eget enim, ultrices nulla feugiat porta fringilla pellentesque vulputate.

F R A G R A N C E S

Donec mauris purus sodales eget enim, ultrices nulla feugiat porta fringilla pellentesque vulputate.

Q U A L I T Y   C O N T R O L

E C O   C A R E

G L A S S    Q U A L I T Y

W A X   C A R E

W E   T A K E   C A R E

Donec mauris purus sodales eget enim, ultrices nulla feugiat porta fringilla pellentesque vulputate.

Donec mauris purus sodales eget enim, ultrices nulla feugiat porta fringilla pellentesque vulputate.

Donec mauris purus sodales eget enim, ultrices nulla feugiat porta fringilla pellentesque vulputate.